SeaSucker Monkey Bars Roof Rack Installation - 2022 Chrysler Pacifica- Video
Hey, it's Ethan and here at etrailer. Today we're gonna be taking a look at and showing you how to install the SeaSucker Monkey Bar Roof Rack System on our 2022 Chrysler Pacifica. First thing, we already have our front set up, so we're just gonna be showing you the rear one, but the process is gonna be the same. Make sure you have the dual cup one in the front. Also we're gonna start by cleaning off our roof, just soapy water, anything like that to get that dust and debris off the top so we have a nice firm hold. And we're gonna take off these plastic caps, so we make sure you keep them around 'cause we will have to put them back on anytime we take these off. more
5/15/2023 2:15:00 PM
Inno Roof Rack Review - 2015 Chrysler 300- Video
Today on our 2015 Chrysler 300, we're doing a test fit of the NL Aero Crossbars. The part numbers for the crossbars we're using is INXB108 on our front bar, and our back bar is INXB115. For our flush fit pack here, we're using INXS200, and for our fit kit for the Chrysler we're using INK433. I've already got my back bar here, my front one's on, got one side installed. We're going to show you how to put this flush fit pack together, and then how we install the back bar. We'll start by taking our rubber pad, and we're going to have the lip here closer to the inside of the foot pack. more
1/14/2016 8:26:45 AM
Rhino-Rack Aero Roof Rack Installation - 2013 Chrysler 200 DA126- Video
Today on our 2013 Chrysler 200, we'll be test fitting the Rhino-Rack 2500 Series Roof Rack with Aero crossbars 50 inches long in silver part number DA126. We'll also be using the Rhino-Rack part Fit Kit part number DK317. With our roof rack system assembled according to the instructions, we'll begin our test fit by opening both front doors, then we'll grab our front bar and place it under the front part of our roof. To make sure we have these aligned in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our leg foot plate. We'll do this measurement on both sides to ensure that our feet are in line with each other. We can then use the Allen key to tighten down the Allen bolt on the inside of the Flip pac to secure our clamps around the roof line of our vehicle. We'll do this on both sides of the vehicle until we have our front bar full secured. more
11/5/2013 10:00:22 AM
Rhino-Rack Aero Roof Rack Installation - 2013 Chrysler 200- Video
Today on our 2013 Chrysler 200, well be test fitting the Rhino-Rack 2500 Series Roof Rack with Aero Crossbars, 50" long in black, part number DA126B. Well also be using our Fit Kit, part number DK317. With our roof rack system assembled according to the instructions, well begin our test fit by opening our front doors. Well grab our front bar and place it onto the front part of our roof. To make sure that we have this bar in the right location, well measure 28 cm from the center of our doorjamb, to the center of our foot plate. Well do this measurement on both sides to ensure that our feet are in line with each other. Well use an Allen key to tight down our Allen bolt, which will secure our clamps around the roofline of our vehicle. Well do this for both sides of our front bar. more
11/5/2013 10:00:22 AM
Rhino-Rack Euro Square Roof Rack Installation - 2013 Chrysler 200- Video
Today on our 2013 Chrysler 200, well be test-fitting the Rhino Rack square bars 2500 series Roof Rack, 49 inches long, using part number DS126B, and the fit kit DK317. With our roof rack system assembled according to the instructions, well begin our test fit by opening our front doors. Well grab our front bar, and place it unto the front part of our roof. To make sure that we have this bar in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our footplate. Well do this measurement on both sides to ensure that out feet are inline with each other.Then we can use the Allen key to tighten down our Allen bolt, which will secure our clamp around the roofline of our vehicle. Well make our way from side to side tightening it a little at a time, to make sure we dont lose our position. more
11/5/2013 10:00:22 AM
Rhino-Rack Heavy-Duty Roof Rack Installation - 2013 Chrysler 200- Video
Today on our 2013 Chrysler 200, well be test-fitting the Rhino Rack 2500 series Roof Rack, with the heavy duty crossbars 50 inches long in silver, using part number DH1250S, and DK317 for our fit kit. With our roof rack assembled according to the instructions, well begin our test fit by opening both front doors. Well grab our front bar and place it under the front part of our roof. To ensure that we have this bar in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our footplate. Well do this measurement on both sides to ensure that out feet are inline with each other.Then well use an Allen tool to tighten down our Allen bolt, which will secure our fit around the roofline of our car. Well make our way back and forth tightening a little out of time, so we dont lose our position. more
11/5/2013 10:00:22 AM
Yakima Q Tower Roof Rack Installation - 2013 Chrysler 200- Video
Today on our 2013 Chrysler 200 well be test fitting the Yakima Round Bar Roof Rack System, part numbers Y00409, Y00696, Y00606, and Y00124. With our crossbars already assembled according the Yakima fit lookup or the included instructions well place the front crossbar onto the vehicle. Well then need to measure from the front part of the glass to the first part of the tower. This measurement is included again in the Yakima fit lookup or the included instructions. Well measure eight inches on the drivers side and passenger side of the vehicle to make sure that the crossbar is perpendicular to the vehicle. Once weve established this position onto the roof or our vehicle, well tighten down the bolt on the inside of the tower and secure the tower by clamping down the black plastic cap. more
3/28/2013 12:06:27 PM
Thule Traverse Roof Rack Installation - 2004 Chrysler PT Cruiser- Video
Today on this 2004 PT Cruiser, we are going to do a test fit of a Thule Roof Rack System. We will be using the Traverse Foot Pack with the 50 long load bars. Now we have our load bars already assembled according to the instructions, its a matter of just setting them in the right place on our car. Now we already have the doors open so lets get started on the first crossbar. First go ahead and lay it on the roof, and then we will get our measurement to properly position it. Now always go by the instructions. more
12/7/2011 10:49:42 AM
Rhino Rack Roof Rack Installation - 2007 Chrysler Town and Country- Video
Today we inchesre looking at it 2007 Chrysler Town and Country we will be test fitting the rhino roof rack system part number SXB4-SILV. We inchesve already got our load bar set up so let inchess go ahead and install it on the vehicle. When installing your load bars you want to make sure that you are perpendicular to the existing roof rails. This particular application has a mark on the side of the rails that will allow us to use that as an indicator. One I am perpendicular to the roof rails I want to make sure I am centered side to side and the overhang is roughly the same. I can go ahead and take my installation tool that is provided in our install kit and tighten them down. more
12/1/2011 3:07:25 PM
Thule Crossroad Roof Rack Installation - 2008 Chrysler Aspen- Video
Today on this 2008 Chrysler Aspen with factory raised side rails we are going to install a Thule Crossroad roof rack system. We already have our crossbar assemblies put together and now we are ready to go ahead and mount them up on our side rails. There is a few things that you are going to want to make sure to do when positioning the roof rack. First you need to check to make sure that the overhang of the crossbars is even on both the driver side and the passenger side. The last thing we need to do is make sure that our new crossbar is running perpendicular with our factory raised side rails. To do that we are going to measure from the crossroad foot to the front mount of the side rail on both sides of the vehicle and make sure this measurement is even. Once we have our positioning set we are ready to tighten down the front bar assembly we will move back and forth from the passenger side to the driver side to make sure that we tighten down the system evenly. After we have the front crossbar tightened down we are ready to mount the rear. :54 more
9/14/2011 11:22:50 AM
Rhino Rack Roof Rack Installation - 2008 Chrysler Aspen- Video
Today on this 2008 Chrysler Aspen we will be installing a Rhino Rack roof rack part number SXB4-SILV. We already have our crossbar assemblies put together so now we are ready to mount them up on our vehicle. We want to check the overhang of the crossbar on both the driver side and passenger side to make sure it is even. We need to ensure that the front crossbar is running perpendicular to our factory raised side rails. To do this we will measure from the end of the clamp to the front plastic shroud on our side rails and make sure this measurement is even on both sides. Once we have the front crossbar assembly in place we can go ahead and begin tightening it down. We will move back and forth from the passenger side to the drivers side so we tighten down the roof rack system evenly and we do not lose our position. more
9/13/2011 1:21:23 AM
Filter Videos
Filter Videos
